Видео

Great video. I just did this. It works. Thanks

I would just put 2 nuts on the outer tie rod and remove the inner that way.

Thanks. Mine leaks badly, likely the same crack, but I can not see it. Hey, 1750 psi, what should we expect. In my case into the garbage can and order new wand. I have used JB weld successfully before, but that was 40 years ago. Not this time.

hello lakay. another lakay here but from australia. can i ask your expertise pls. mine is 2010 mazda 3 2.0. randomly engine is cutting off when you reverse especially when its cold. no dtc or any faults during scanning. any idea whats happening lakay. salamat lakay

Same code p0746, my car drives and runs but doesn't shift to next gear..what do you think?

Thank you kuya good job

Do you know wich type of transmission fluid needs? I need to change it but i dont have the owners manual

Did all that still got code and the car is getting hot and smoking

The tool never said anything about vent solenoid canister

The fan you’re referring to is the radiator fan or the condenser fan?

Don't you need to purge the coolant after all the procedure?

Thank You. I think, this is what happened to my car, as well.

Tnx bro

Keep up the good work my friend your videos really help alot 👏 👍

where are you located? I need mine done & definitely not going to do it.

thank you for this video rear calipers where giving me a hard time

I have a 2012 versa and I removed the upstream 02 sensor. I didn’t have to remove the throttle body nor the front tubing with the 6 screws. That’s a lot of work you have created. Just saying😮

good job bro

Thank you! This was able to help me confirm where the water leak was coming from and the cause of it :D

You don’t have to change the whole strut assembly unless you want to. The noise is coming from the top strut mount bearing. I personally just bought a strut mount with a bearing and replaced it and that’s solved the issue.

Hi thanks for the video. It will be a big help when I do mine. Do I need to bleed my brakes after doing this ?

how come you didnt show torquing them down? that was tricky for me can you also do a timing belt video on this engine w tensioner explained

Never ever again japanese trash car

Do you know part number?

What's the belt size I have this same engine and can't find the belt

Ons of the most rubbish car in world

Best video on RUclips for the 4.0 water pump. Greatly appreciated. Subscribed.

I'm lost. Why do you have 2 negative poles on the fan sensor

I didn't see how you pull it out with the chain,did you just strap the chain and put it out by the chain or did you use some to pull on the chain?

Thank you for this video!! I’ve been looking to replace this for months.

1. Use penetrating fluid. 2. Use a wire brush on the threads before removing nuts.

Kabayan, yan din kaya ang problema kapag nililipat ko po ang gear from park-drive-reverse. May parang nag babang or may nalagutok kapag nag lilipat po ako ng gear. Salamat po!

thanks bro

Ty so much, this video was really informative and helpful

You did not bench test that starter properly, there was no starter to battery connection only starter signal voltage applied!

So rough 😞

So mine only goes in reverse and not foward , machanic said it was transmisión but it was replaced snd does the same

this is NOT the correct way to service a CVT transmission in a 2015 versa note! you can't just replace what you take out due to the fact that if you are even slightly over or slightly under the required fluid amount the running pressures will change causing the transition to slip or sustain permanent damage! there are videos here on YT that illustrate the correct procedure which involves running the vehicle until operating temperature is reached, loading up the draining off the access fluid!

I changed 2 actuators. They took too long. In the second, I broke a couple of bracket and got frustrated after 4 hours. I removed the glass in 5 minutes and then it took me another 10 minutes to install the lock mechanism. I highly suggest removing glass and weather strip around the glass.

So no carjack under the car to hold motor? Just wondering because I had to do that to the Integra.

What is that big black plug go into?

.07mm. intake Exhaust 9

I have the same problem then I replaced the hose but my steering is really really stiff it is very hard to turn in parking and turning 3 way turn do you know what is the problem and how to fix it?

Have you done the sparkplugs yet

What was the size of the socket, please?

Why'd you loosen the fender and bumper cover?

Would a failed water pump leak from that same area because my car is leaking antifreeze like from the same area and i feel like it leaks wen the car starts heating up and eventually starts smoking cuz the antifreeze makes contact with the hot components mechanic told me it was a failed water pump car is also dried up on antifreeze

Good explanation, thanks bro , u solved my problem

My code is p06b8 how do I delete the engine light without a machine?? How can I program my remote keys to the car?

te lo agradezco, ya no sabia que hacer.